| STRUDDER PACKAGE 93 |
this strudder package is designed for
22-3Occ gas engines installed in deep vees. This strudder allows the cable to be brought
out the back of the boat (surfacing application),instead of the bottom. It comes with the
OC8SBE strut blade (which has a 45 degree
back sweep) with
2 - OC10RB916 reducers and
4 - OC8LTS lead teflon sleeve bearings
installed, 1/4"dia prop shaft with
OC8DT tapered drive dog and
tail nut (OC8PNM)
OCFSF916 flex ferrule.
OC8TW thrust washers and offset rudder (with water pick up
hole extruded directly into the rudder blade), all mounted in the back hole of our
standard extruded aluminum mounting bracket. Comes with 21 of 1/4"(.250) flex cable
(std. left lay) with one end squared and 21 of teflon tubing (SEE ILLUSTRATION) (note
: flex ferrule and flex cable are not joined together)
THIS PACKAGE IS DESIGNED WITH THE SERIOUS RACER IN MIND - THE OFFSET RUDDER MAKES THE BOAT
VERY MANEUVERABLE ON A RACE COURSE - MAKING RIGHT HAND TURNS IS WHAT THIS STRUDDER IS
DESIGNED FOR |
83.95 |
| STRUDDER PACKAGE 93C |
same as above but with a cast aluminum
mounting bracket pulling the assembly in 2" closer to the stern of the boat |
T.B.A. |
| OC8STR-Q |
strudder package is designed for 22 - 3Occ
gas engines (if the assembly is installed in a deep vee, the cable would be brought out
the bottom of the boat for a submerged propeller application) This package comes complete
with large rudder assembly with a larger pivot bracket than standard strudder (which
allows installation of large 1/4"bore propellers while keeping the rudder in
line),large stainless steel strut blade with
2 - OC8LTS lead teflon sleeve bearings) and
2 - OC10RB (reducer bushings) installed,
1 - OC8PS (1/4" dia. prop shaft with drive dog and tail
nut) and
OC8TW (thrust washers) on standard extruded aluminum
mounting bracket with
OCFSF2525 (flex ferrule) and 21" of
1/4" (.250) dia. flex cable with one end squared and 21" of teflon tubing (SEE
ILLUSTRATION ) (note : ferrule and cable are not joined together) |
78.95 |
| OC8STR-C |
strudder package same as above except the
flex cable does not have a squared end - |
78.95 |
| PACKAGE 94SS |
package is similar the the standard PACKAGE
94 but it comes with a 1/4"prop shaft and 1/4" flex cable. It also includes the
SSSLBO (large stainless steel strut
blade) with
2 - OC8LTS (sleeve bearings) and
2 - OC10RB (reducer bushings) installed,
the OC8PS (1/4"prop shaft, drive dog and tailnut),
OCFSF2525 (flex ferrule) and 21 .250 flex
cable and- matching tubing. This package also comes with the OC6WRL large wedge rudder assembly. This
package would be used with 22 - 30cc gas engines in hulls where a separate strut and
rudder is desired (such as a hydro) - |
76.95 |
| STRUDDER PACKAGE '92 |
This package is designed for use with .60
to .80 nitro engines and comes complete with STRUDDER M, with
2 - OC6LTS (sleeve bearings) &
2 - OC8RB (reducers),
1 - OC6PSM (3/16" dia. prop shaft with drive dog),
1 - OC6TWM (thrust washers),
1 - OC6PNM (prop tail nut),
1 - OCF5F1818 (flex ferrule),and 21 of
3/16" (.187) dia. flex cable and 21 of matching teflon tubing. (ferrule and cable are
not joined together) |
49.95 |
| STRUDDER PACKAGE '92Q |
same as above but with OC6SQL-24A (.187 cable with one end squared) |
52.95 |
| STRUDDER PACKAGE '92B |
this package is similar to the package 92
but this one has a 7.5 degree angle on the mounting bracket |
50.95 |
| STRUDDER PACKAGE '92C |
this package is similar to the package 92
but the rudder is offset to one side on two stainless steel rods |
54.65 |
| STRUDDER PACKAGE '92D |
this package is similar to the package 92C
with the offset rudder but it also comes with the 7.5 degree angle mounting bracket |
55.65 |
| PACKAGE 94 |
this package is designed for .60 - .80
nitro engines with hulls where a separate strut and rudder is preferred (such as a hydro)
this package comes with a 3/16" prop shaft and 3/16" flex cable strut and
rudder. It comes with the
DVMAS - profiled strut blade with mounting
bracket,
2 - OC6LTS (sleeve bearings) and
2 - OC8RB (reducer bushing) installed,
OC6PS (3/16" prop shaft with drive dog),
OC6TW (thrust washers),
OC6PNM (prop tail nut) and 21 .187 flex cable and matching
teflon tubing and the
OCFSF1818 (flex ferrule). This package also
has the
OC6WRL large wedge rudder assembly with
the new rudder blade with the sole extruded directly into it and uniquely machines at the
top so the water pick up flow is not restricted |
54.95 |
| PACKAGE 97S |
this strut and rudder package is designed
for use with .40 nitro engines. It comes complete with the
OC6SB40 (cast strut blade with sleeve
bearings)
OC6SBBR40 (cast aluminum mounting bracket),
OC6PSM (prop shaft with drive dog),
OC6TWM (thrust washer set),
OC6PNM (prop tail nut),
OCFSF616 (flex ferrule) and
OC187L-24B (24" .187 left lay flex cable
and matching teflon tubing) and also the
OC6WR40 (aluminum wedge rudder assembly
with mounting bracket) |
73.95 |
| STRUDDER PACKAGE 97 |
this strudder package is designed for .40
nitro engines and comes complete with strut and rudder on a single mounting bracket, .187
flex cable and matching teflon tubing |
T.B.A. |
| OC6STR-150 |
STRUDDER ASSEMBLY with
OC4WRMC (rudder assembly),
OC4STBR (strudder bracket), with the
OC6SBEPA-150 (strut blade with sleeve
bearings and nose piece installed),
OC6DMN (drive dog),
OC6150PS (3/16" prop shaft with retaining nut), washer and
18"of .150 flex cable (standard left lay) and 18" teflon tubing. (OC6150PS and cable are not joined)-can be used with geared
electrics and .21 nitro engines
(beryllium copper)
 |
56.95 |
| OC6STR-150A |
STRUDDER ASSEMBLY same as above but in
aluminum |
56.95 |
| PACKAGE 96-15 |
package includes
OC6SBCOML-150 strut assembly and
the
OC4WRM wedge rudder assembly - designed for use
with .21 nitro engines and geared electrics - for use on hulls where separate strut and
rudder is preferred (beryllium copper) |
66.75 |
| PACKAGE 96-15A |
same package as above but in aluminum |
66.75 |
| OC6STR-130 |
STRUDDER ASSEMBLY with
OC4WRMC (rudder assembly),
OC4STBR (strudder bracket), with the
OC6SBEPA-130 (strut blade with sleeve
bearings and nose piece installed),
OC6DMM (drive dog),
OC6130PS (3/16" prop shaft with retaining nut), washer and
18"of .130 flex cable (standard left lay) and 18" teflon tubing (OC6130PS and cable are not joined) can be used with geared
electics - (beryllium copper) |
56.95 |
| OC6STR-130A |
STRUDDDER ASSEMBLY same as above but in
aluminum |
56.95 |
| PACKAGE 96-13 |
package includes OC6SBCOML-130 strut assembly and the
OC4WRM wedge rudder assembly - designed
for used with geared electrics - for use on hulls where separate strut and rudder is
preferred (beryllium copper) |
66.75 |
| PACKAGE 96-13A |
same package as above but in aluminum |
66.75 |
| OC6STR-64 |
STRUDDER ASSEMBLY similiar to the
OC6STR-130 (listed above) but with a .187 prop shaft counted bored for the .130 flex
cable, but the prop shaft is stepped done to .125 - it come with the
OC4D (drive dog),
OC4PN (prop nutt) and an .125 ID washer. This strudder is
designed to be used on .10 - .15 engines wnich need a stronger .130 cable but will still
accommodate a .125 bore propeller. (beryllium copper) |
58.95 |
| OC6STR-64A |
STRUDDER ASSEMBLY same as above but in
aluminum |
58.95 |
| PACKAGE 96-64 |
STRUT AND RUDDER PACKAGE FOR .10-.15 nitro
boat where a separate strut and rudder is desir6d-comes with OC6SBCOML-64 strut package
and OC4WRM wedge rudder assembly
(beryllium copper) |
68.75 |
| OC4STR-C |
STRUDDER ASSEMBLY with
OC4WBE (wedge blade),
OC4PIBR (pivot bracket),
OC4PISH (pivot shaft),
OC4SBEPA (strut blade with sleeve
bearings and nose piece installed),
OC4D (drive dog),
OC4PS (1/8"prop shaft),
OC4PN (prop tail nut),
OC4STBR (strudder bracket) and a washer with 18".098
flex cable standard left lay) and 18"teflon tubing (OC4PS and cable not joined) (SEE
ILLUSTRATION
) |
53.95 |
| PACKAGE 95 |
package includes
OC4SBCOML strut assembly (with
.125 prop shaft and .098 cable) and
OC4WR wedge rudder assembly- ideal for
direct drive electric hull where a separate strut and rudder is preferred (beryllium
copper) |
62.35 |
| PACKAGE 95A |
same as above but in aluminum |
62.35 |
|
 SEPARATE STRUT PACKAGES FOR SMALLER BOATS
all of the hardware listed below is available in beryllium copper or aluminum. While
the price is the same between the aluminum and the beryllium copper, the aluminum is
lighter but the beryllium copper is stronger. Beryllium copper will be shipped unless
aluminum is specified. |
| OC6SBCOML-150 |
STRUT ASSEMBLY-designed for use with .21
nitro engines or geared electrics- it comes with
OC6SBE (strut blade) with
2 - OC6LTS (sleeve bearings),
OC61SONP (nose piece),
OC6150PS (prop shaft),
OC6DMM (drive dog),
OC4SBBR (mounting bracket), a washer, retaining nut and a 4/40
socket head wrench (for the drive dog set screw) with 18"of .150 flexible cable
(standard left lay) and 18"of .150 teflon tubing (OC6150PS and cable not joined) |
31.95 |
| OC6SBCOML-130 |
STRUT ASSEMBLY - designed to be used with
geared electrics -the assembly comes with
OC6SBE (strut blade) with
2 - OC6LTS (sleeve bearings),
OC613ONP (nose piece),
OC6130PS (prop shaft),
OC6DMM (drive dog),
OC4SBBR (mounting bracket), a washer, a retaining nut and a 4/40
socket head wrench (for the drive dog set screw) with 18"of .130 flexible cable
(standard left lay) and 18"of .130 teflon tubing (OC6130PS and cable not joined) |
31.95 |
| OC6SBCOML-64 |
STRUT ASSEMBLY - design for use with .10 -
.15 nitro engines, this strut assembly comes with a
strut blade (OC6SBE) with
sleeve bearings (OC6LTS) and
nose piece (OC613ONP) installed,
mounting bracket (OC4SBBR), and a stepped 3/16";@18"prop
shaft (which is counter bored for a .130 flex cable),
drive dog (OC4D),
prop tail nut (OC4PN), a washer and 18" .130 flex cable
and matching teflon tubing. It has the strength of a .130 flex cable but the stepped prop
shaft allows the use of 1/8"bore propellers which is what most .10 - .15 engines can
swing. (cable and prop shaft are not joined) |
33.95 |
| OC4SBCOML |
STRUT ASSEMBLY - same as above but with
18"of .098 flexible cable (standard left lay)and 18"of .098 teflon tubing (OC4PS
and cable not joined) |
31.95 |
| OC4SBCOMR |
STRUT ASSEMBLY - same as above but with
right lay flexible cable |
31.95 |
| OC4WR |
WEDGE RUDDER ASSEMBLY with an
OC4WBE (cast wedge rudder blade),
OC4PIBR (pivot bracket),
OC4PISH (pivot shaft) and
OC4SBBR (mounting bracket)
(SEE ILLUSTRATION
) beryllium copper -for use with direct drive electrics or
smaller nitro hulls |
30.45 |
| OC4WRM |
WEDGE RUDDER ASSEMBLY with a cast rudder bladelpivot
bracket assembly 25% larger than the OC4WR. This rudder is can be used on direct drive
electric, geared electrics or .15 - .21 nitro engines. Comes with two sided (push/pull)
tiller arm and OC4SBBR (mounting bracket). (beryllium copper) |
34.95 |
| OC6WR40 |
cast aluminum wedge rudder, pivot bracket and mounting
bracket, pivot shaft, and the necessary sleeve bearings and washers and nuts and bolts all
assembled. (Please note- this blade is cast so you will need a separate water pick
up.)(See illustration) |
37.95 |
| OC6WRL |
LARGE WEDGE RUDDER complete assembly consists of an
aluminum stern mounting bracket, rudder blade with water tube extrudes up the back of the
blade with a water pick up machined in the side of the rudder blade, 2 nylon tiller arms,
rudder pivot shaft, bearings & four t-nuts & bolts for mounting (rudder blade
measure 3 1/2" from underside of tilyer arm to the bottom of the blade)(water pick up
is available machined on the right or the left side, if you have a preference please let
us know when ordering) This rudder will work with -60 nitros and larger. (extruded
aluminum mounting bracket is 1 3/4" high by 1 1/4"wide) |
12.95 |
| OC6WRL2 |
LARGE WEDGE RUDDER complete assembly consists of an
cast aluminum stern mounting bracket with an extruded aluminum pivot bracket (this puts
the leading edge of the rudder blade approx. 2 inches from the stern of the boat), wedge
rudder blade with water tube extruded up the back.of the blade, and a pick up machined at
the lower edge, 2-nylon tiller arms, rudder Pivot shaft, bearings and four t-nuts &
bolts for mounting. (rudder blade measures 3 1/2" from underside of tiller arms to
the bottom of the blade) (see illustration) |
33.50 |
| |
PLEASE NOTE STRUTS AND STRUDDERS LISTED BELOW DO NOT
NORMALLY COME WITH BEARINGS INSTALLED - HERE ARE THE RECOMMENDED INSTALLATIONS (BEARINGS,
REDUCERS, ETC. ARE LISTED ON PAGE 8) FOR 3/16" DIA. PROP SHAFT AND .187 FLEX CABLE
JOINED WITH .187 -.187 FERRULE USE ONE OF THE FOLLOWING: |
|
| |
2 NEEDLE BEARINGS (OC6NE) or
|
|
| |
2 SLEEVE BEARINGS (OC6LTS) with
2 REDUCERS (OCSRB) or
|
|
| |
1 NEEDLE BEARING (OC6NE) with
1 SLEEVE BEARING (OC6LTS) &
1 REDUCER (OC8RB) FOR 3/16" DIA. PROP SHAFT AND .250
FLEX CABLE JOINED WITH .250 -.187 FERRULE USE THE SAME AS ABOVE.
|
|
| |
FOR 1/4 DIA PROP SHAFT AND .250 FLEX CABLE JOINED
WITH.250-.250 FERRULE USE THE FOLLOWING: |
|
| |
2 SLEEVE BEARINGS (OC8LTS) with
2 REDUCERS (OC1ORB) FOR USE WITH .187 DIA. FLEX CABLE WITH
ATTACHED 3/16" PROP SHAFT (PRESOLDERED PROP SHAFT/ CABLE NOT AVAILABLE FROM OCTURA)
|
|
| |
1 NOSE PIECE (OC8NP),
2 SLEEVE BEARINGS (OC6LTS) and
1 REDUCER (OC8RB) or
|
|
| |
1 NOSE PIECE (OC8NP),
1 SLEEVE BEARING (OC6LTS) and
1 NEEDLE BEARING (OC6RE)
|
|
| DVAS |
DEEP VEE ADJUSTABLE STRUT. Stern or through
hull mounting. From lower edge of bracket to center of prop shaft: 2 3/16" maximum -
1 3/16" minimum. Consists of OC6SBBR (cast aluminum mounting
bracket 1 1/4" wide 2"long), DVBO
strut blade (extruded aluminum)bored 11/32",10-32 bolt/lock nut and 4 6-32
t-nuts/bolts for mounting - |
18.95 |
| DVMAS |
DEEP VEE M ADJUSTABLE STRUT. Same as above
but with DVMBO strut blade machine
profiled to streamline shape - bored 11/32 |
19.95 |
| SDAS |
SURFACE DRIVE ADJUSTABLE STRUT. Flat bottom
strut for stern or through hull mounting.
From lower edge of mounting bracket to center of prop shaft:l 518"maximum -
518"minimum.
Consists of OC6SBBR (cast aluminum mounting bracket), SDBO flat bottom strut blade bored
11/32",10,-32 bolt/lock nut and four 6-32 t-nuts & bolts for mounting |
19.95 |
| STRUDM |
STRUDDER M. Complete strut/rudder assembly,
one mounting bracket with directly behind strut. Consists of support bracket, wedge
rudder,water pick up tube,2 nylon tiller arms (TA-2),rudder
pivot bracket,pivot shaft & rudder pivot bearings, 4 T nuts & screws and shaft
support (strut) blade machine profiled to streamlined shape (DVMBO) bored 11/32 |
27.95 |
| STRUD75 |
STRUDDER 7.5 M. Same as above but with 7.5
degree angle on mounting bracket |
28.95 |
| STRUD2D |
TWIN DRIVE STRUDDER M. Same features as
strudder but for twin drive applications.
Consists of two support brackets complete with strut blades with wedge rudder assembly
centered between on stainless steel rods (SEE ILLUSTRATION ON PAGE 24) |
49.95 |
| STRUD2D7 |
TWIN DRIVE STRUDDER 7.5 M. Same as above
but with 7.5 degree angle |
50.95 |
| STRUD2R |
TWIN RUDDER STRUDDER M. similar to strudder
but with twin rudders. Consists of one support bracket with strut blade centered(on
stainless steel rods) between two wedge rudder assemblies (SEE ILLUSTRATION ON PAGE 24) |
42.95 |
| STRUDOFF |
OFFSET STRUDDER M. Similar to strudder but
with rudder offset. Consists of support bracket with strut blade, with stainless steel
rods supporting rudder assembly off center (SEE ILLUSTRATION ON PAGE 24) |
31.95 |
| STRUDOF7 |
OFFSET STRUDDER 7.5 M. Same as above but
with 7.5 degree angle |
32.95 |
|
PROP
SHAFTS |
| OC4PS |
STAINLESS STEEL PROP STUB SHAFT 1/8"
O.D. counter bored for .098cable, 5/16" dee with the opposite end threaded 5-40 ,
2" overall length |
2.59 |
| OC6130PS |
STAINLESS STEEL PROP STUB SHAFT 3/16"
dia., counter bored .130, 1/2"deep with opposite end threaded 10-32, 2
1/4"overall length, with retaining nut |
3.00 |
| OC6150PS |
STAINLESS STEEL PROP STUB SHAFT 3/16"
dia., counter bored .150, 1/2"deep with opposite end threaded 10-32, 2
1/4"overall length, with retaining nut |
3.00 |
| OC6PS |
3/16" DIAMETER PROP STUB SHAFT WITH OC6D (7/16" O.D.drive dog), 3 1/4"long, 10-32 thread. Do
NOT use with needle bearings |
3.65 |
| OC6PSM |
PROP STUB SHAFT WITH OC6DM
(3/8"O.D. drive dog)(same shaft as above) - |
3.65 |
| OC6PSL |
3/16" DIAMETER PROP STUB SHAFT WITH OC6D (7/16.'0.D.drive dog), 4 1/4"long, 10-32 thread. Do NOT
use with needle bearings. Designed to be used with cast stainless steel or cast aluminum
strut blades listed on page 6.Flats already filed for drive dog and flex ferrule set
screws |
5.25 |
| OC6PSH |
3/161. DIAMETER UNTHREADED HARDENED PROP
STUB SHAFT WITH OC6D (7/16"O.D. drive dog) 3 1/2"long
for use with needle bearings - |
6.50 |
| OC6PSEM |
UNTHREADED HARDENED PROP STUB SHAFT WITH OC6DM (3/8" O.D. drive dog) same shaft as above |
6.50 |
| OC68PS |
STEPPED PROP SHAFT - This prop shaft is
designed to be used with 1/4"sleeve bearings, but it is stepped down to 3/16" at
the propeller end. It comes with thrust washers (OC6TW),
prop nut (OC6PNM) and drive dog (OC6D) |
9.95 |
| OCSPSH |
1/4" DIAMETER UNTHREADED HARDENED PROP
STUB SHAFT WITH OC8D (drive dog), 4" long and OC8PNU (prop nut) |
10.95 |
| OCAPS |
1/4" DIAMETER PROP STUB SHAFT with
OC8D (drive dog) and OC8PNM (prop tail nut), 4 112"long
with flats filed for drive dog and flex ferrule, long enough to be used with any of the
cast strut blades listed on page 6 on sleeve bearings (Do not use with needle bearings) |
9.50 |
|
PROP TAIL NUTS |
| OC4PN |
STREAMLINED PROP TAIL NUT, fits 5-40 thread
on an 1/8"(.125) dia. shaft, 7/32 hex, 9/16" long, brass |
1.85 |
| OC6PNMK |
STREAMLINED PROP TAIL NUT,fits 10-32 thread
on a 3/16"(.187)dia. shaft, 5/16" dia., 5/8 "long, 1/4 flats, brass (this
is a good size to match the hubs on our pro from approx. 37mm-42mm - .21 nitro engine
size) |
1.555 |
| OC6PNM |
STREAMLINED PROP TAIL NUT, fits 10-32
thread on a 3/16"(.187)dia. shaft, 3/8"dia., 3/4 "long, 5/16 flats,
hardened plated steel |
2.35 |
| OC6PN |
STREAMLINED PROP TAIL NUT, fits 10-32
thread on a 3/16"(.187) dia. shaft, 7/16" dia., 13/16" long,
3/8"flats, hardened plated steel |
2.35 |
| OC6PNMU |
STREAMLINED PROP TAIL NUT, fits smooth
3/16" (.187) diameter shaft, 3/8"dia., 314"long with 8/32 set screw,
(unthreaded) hardened plated steel |
2.35 |
| OC6PNS |
STREAMLINED PROP TAIL NUT, fits 10-32
thread on a 3/16"(.187) dia.shaft, 7/16" dia.,13/16" long w/ 8/32 set screw
, hardened plated steel |
2.35 |
| OC6PNMS |
STREAMLINED PROP TAIL NUT,fits 10-32 thread
on a 3/16"(.187) dia.shaft, 3/8" dia., 3/4" long w/ 8/32 set screw,
hardened plated steel |
2.35 |
| OCSPNU |
STREAMLINED PROP TAIL NUT, fits smooth
1/4" (.250) diameter shaft, 7/16" dia., 13/16" long w/ 8/32 set
screw,(unthreaded) hardened plated steel |
2.35 |
| OC8PNM |
STREAMLINED PROP TAIL NUT, fits 1/4-28
thread on a 1/4"(.250) dia.shaft, 3/8" hex, 15/16" long, brass |
2.15 |
|
THRUST WASHERS |
| OC4TW |
THRUST WASHER SET (consisting of 2 metal
washers and 2 moly-nylon washers) 1/8" bore |
.75 |
| OC6TWM |
THRUST WASHER SET (same as
above)3/16", bore 3/8" O.D. 3/16" long |
1.45 |
| OC6TW |
THRUST WASHER SET (consisting of 2 hardened
steel and 2 moly-nylon washers) 3/16" bore, 7/16" O.D. 3/16" long |
1.65 |
| OC8TW |
THRUST WASHER SET (same as above)
1/4", bore 1/2" O.D. 3/16" long |
1.85 |
|
DRIVE
DOGS |
| OC4D |
DRIVE DOG, 1/8" bore, 1/4"
diameter, with 4/40 set screw, brass |
1.85 |
| OC6DMM |
DRIVE DOG, 3/16" bore, 5/16"
dia., w/ 4/40 set screw, hardened plated steel |
1.85 |
| OC6DM |
DRIVE DOG, 3/16" bore, 3/8" dia.,
w/ 8/32 set screw, hardened plated steel |
1.85 |
| OC6DT |
DRIVE DOG, 3/16" bore, 7/16" to
3/8" tapered outside diameter, with 8/32 set screw, hardened plated steel - |
1.95 |
| OC6D |
DRIVE DOG, 3/16" bore,7/16" dia.,
w/ 8/32 set screw, hardened plated steel |
1.85 |
| OC6DD |
DRIVE DOG, 3/16" bore,7/16" dia.,
w/ two 8/32 set screws,hardened pltd steel |
2.35 |
| OCSD |
DRIVE DOG, 1/4" bore, 1/2"' dia.,
w/ two 8/32 set screws, hardened plated steel |
2.35 |
| OC8DM |
DRIVE DOG, 1/4" bore, 7/16" dia.,
w/ 8/32 set screw,hardened plated steel |
1.95 |
| OC8DT |
DRIVE DOG, as used in the STRUDDER PACKAGE 93, 1/4" bore
with 9/161'dia. tapered to 15/32", with two 8-32 set screws, hardened plated steel |
2.45 |
| OC6D5 |
DRIVE DOG, SYM bore,7/16" dia., with
8/32 set screw, hardened plated steel |
1.85 |
| OC6DH |
DRIVE DOG, 3/16" bore,7/16" dia.,
with 8/32 set screw - stainless steel |
2.75 |
|
BALL THRUST BEARINGS |
| OC6TB |
BALL THRUST BEARING SET (consisting of a
ball retainer and two hardened steel washers) 3/16" bore, 7/16" O.D. 3/16"
long - |
8.75 |
| OC8TB |
BALL THRUST BEARING SET (consisting of A
ball retainer and two hardened steel washers) 1/4" bore |
8.85 |
|
NOSE
PIECES |
| OC4NP |
NOSE PIECE, (brass), for use with .098
cable, to .125 prop shaft (OC4PS) in our OC4SBE strut blade |
1.45 |
| OC613ONP |
NOSE PIECE, (brass), for use with .130
cable, to .187 prop shaft (OC6130PS) in our OC6SBE strut blade |
1.45 |
| OC61SONP |
NOSE PIECE, (brass), for use with .150
cable, to .187 prop shaft (OC6150PS) in our OC6SBE strut blade |
1.45 |
| OC6NP40 |
NOSE PIECE, (brass), for use with .150
cable, to .187 prop shaft (OC6150PS) in our OC6SB40 strut blade |
1.75 |
| OC8NP |
NOSE PIECE 7/16 O.D. with 11/32 dia. boss
to press fit in strudders bord for needle bearings. 1/4" (internal diameter) bore
accepts OC6LTS sleeve bearing and 1/4"
O.D. teflon tubing, for use with 311@ prop shaft and .187 cable.(hardened plated steel) |
1.45 |
|
LEAD TEFLON SLEEVE BEARINGS |
| OC4LTS |
LEAD TEFLON SLEEVE BEARING, 1/8"
(internal diameter) 3/16" O.D. 3/16" long (one in pkg) |
1.15 |
| OC6LTS |
LEAD TEFLON SLEEVE BEARING, 3/16"
(internal diameter) 1/4" O.D. 3/8" long (one in pkg) |
1.20 |
| OC6LTSB |
LEAD TEFLON SLEEVE BEARINGS as above, 5 in
package (saves you 10% over buying them separately) |
5.40 |
| OC8LTS |
LEAD TEFLON SLEEVE BEARING, 1/4"
(internal diameter) 5/16" O.D. 3/8" long (one in pkg) |
1.75 |
| OC8LTSB |
LEAD TEFLON SLEEVE BEARINGS as above, 5 in
package (saves 80 cents over buying them separately) - |
7.95 |
|
REDUCER BUSHINGS |
| OC8RB |
REDUCER BUSHING 11/32.' O.D. 1/4"
(internal diameter) to install 1/4 O.D.x 3/16" (internal diameter) sleeve bearings
(like the OC6LTS) into struts bored 11/32" (plated steel) |
1.00 |
| OC1ORB |
REDUCER BUSHING 11/32" O.D. 5/16"
(internal diameter) to install 5/16" O.D. x 1/4" (internal diameter) sleeve
bearings (like the OC8LTS) into struts bored 11/32" (plated steel) |
1.20 |
| OC1ORB916 |
REDUCER BUSHING 7/16.1 O.D.,5/16"
(internal diameter) to install two 5/16" O.D. sleeve bearings (like the OC8LTS) into
the OC8SBE strut blade (brass) |
1.85 |
| OC68RB |
REDUCER BUSHING for installing .250
(1/4") dia. bore prop to .187 (3/16") dia. shaft machined brass |
1.40 |
|
NEEDLE BEARINGS |
| OC6NE |
NEEDLE BEARING, 3/16" (internal
diameter) 11/32" O.D. rated 30,000 rpm (use only with hardened prop shaft) (sold
individually) |
7.95 |
| OC8NE |
NEEDLE BEARING, 1/4" (internal
diameter) 7/16" O.D. (fits only in strut blades with 7/16" bore) (sold
individually) |
8.00 |
|
STRUT BLADES AVAILABLE SEPARATELY |
| DVBO |
STRUDDER STRUT BLADE OR DEEP VEE ADJUSTABLE
STRUT BLADE ONLY extruded aluminum, non profiled (bored 11/32") |
6.65 |
| DVMBO |
STRUT BLADE ONLY as used in STRUDDER M,
DEEP VEE M ADJUSTABLE STRUT, PACKAGE 92 (Q,B,C,D,) or PACKAGE 94 - extruded aluminum with
underwater section machine profiled (bored 11/32") ( slotted for adjustability) |
7.65 |
| SDBO |
SURFACE DRIVE ADJUSTABLE STRUT BLADE
extruded aluminum with flat bottom (bored 11/32") to be used where the strut blade is
a riding surface |
7.65 |
| OC8SBE2 |
STRUT BLADE this is the strut blade used in
the PACKAGE 93 strudder, manganese bronze with 45 degree back sweep - this is the ONLY one
of our strut blades which will accept 1/4"(internal diameter) needle bearings (OC8NE)
(needle bearings not included) set screw holes machined to allow installation of offset
rudder (rudder offset rods not included) 'trut has 7/16" I.D |
23.95 |
| OC8SBE3 |
STRUT BLADE as above but with 2-OC1ORB916 reducers and 4-OC8LTS lead teflon sleeve bearings with 1/4"
(internal diameter) installed |
32.95 |
| SSSSBO |
CAST STAINLESS STEEL STRUT BLADE with skeg
- bore 11/32" (see illustration) - |
16.95 |
| SSSLBO |
CAST STAINLESS STEEL STRUT BLADE with skeg
- 11/32" bore (see illustration) prop shaft at the same place as with our DVMBO strut
blade. recommended for use with larger gas engines (this is the strut blade that comes on
the OC8STR-Q) |
25.95 |
| SSASBO |
CAST ALUMINUM STRUT BLADE same as SSSSBO
but in aluminum |
15.95 |
| SSALBO |
CAST ALUMINUM STRUT BLADE same as SSSLBO
but in aluminum |
19.95 |
| S U |
STRUT BLADE cast beryllium copper -
designed with scale unlimited hulls or sport 40 hulls in mind. 2 1/4" long, blade 1
1/2"wide & .10011 thick, two slots one inch apart, 3/8"dia. boss - comes
with 2-OC6LTS sleeve bearings installed. (SEE ILLUSTRATION) |
18.00 |
| OC4SBE |
STRUT BLADE, beryllium copper,.250 diameter
shaft housiny.187 dia. bore, with skeg, blade width .687 (use with OC4LTS lead teflon sleeve bearings -2 recommended)
for use with 1/8" dia. prop shaft.
(SEE ILLUSTRATION
) (beryllium copper) |
11.25 |
| OC4SBEPA |
STRUT BLADE - OC4SBE with
2 OC4LTS-lead teflon sleeve bearings and an
OC4NP-nose piece installed (beryllium copper) |
14.25 |
| OC6SBE |
STRUT BLADE, beryllium copper, 5/16"
diameter shaft housing .250 diameter bore. with skeg, blade width .687 (use with OC6LTS - 2 recommended) for use with 3/16"
dia. prop shaft
(SEE ILLUSTRATION
) |
14.25 |
| OC6SBEPA-130 |
STRUT BLADE - OC6SBE (strut blade) with
2 OC6LTS (sleeve bearings) and an
OC613ONP nose piece installed, designed for use with a .130
cable and a .187 prop shaft. (recommended stub shaft - OC6130PS)(beryllium copper)
|
14.25 |
| OC6SBEPA-150 |
STRUT BLADE - OC6SBE (strut blade) with 2 OC6LTS (sleeve bearings) and an OC615OUP nose piece installed. designed for use with a .150 cable
and a .187 prop shaft. (recommended stub shaft - OC6150PS)
(beryllium copper) |
14.25 |
| OC6SB40 |
cast aluminum strut blade for a .45 size
boat, comes with 2-OC6LTS sleeve bearings
installed (see illustration) |
10.95 |
|
BRACKETS |
| OC4SBBR |
BERYLLIUM COPPER MOUNTING BRACKET for strut
blades OC4SBE or OC6SBE,back of the hull or through bottom installation with four 4/40
nuts & bolts and a 5140 socket head bolt with lock nut for clamping. This bracket is
also used in the wedge rudder assembly. This bracket can also be used with OCSKFIN B/0
(SEE ILLUSTRATION)
|
9.95 |
| OC6SBBR |
ADJUSTABLE STRUT BRACKET (cast aluminum)
with four 6-32 t-nuts and bolts for mounting and one 10-32 bolt/lock nut (can be used with
the following strut blades DVBO, DVMBO, SDBO, SSSSBO, SSSLBO, SSASBO, or SSALBO.) (also
used on the OC6WRL2) |
12.95 |
| OC6SBBR40 |
cast aluminum mounting bracket for the
OC6SB40 strut blade (this is also the same mounting bracket used on the OC6WR40 rudder
assembly. Comes with 8-32 bolt/lock nut and four 6-32 t-nuts and bolts for mounting.(See
illustration) |
9.95 |
|
STRUDDER BRACKETS |
| OC4STBR |
STRUDDER BRACKET cast beryllium copper with
two 5140 socket head bolts and lock nuts for clamping and four 4140 nuts and b-olts for
mounting. ( used on the OC4STR/C and the OC6STR-130 7150/64) - |
11.95 |
| OC6STBR |
STRUDDER BRACKET: two piece-extruded
aluminum- with two 10-32 bolts/lock nuts as used on the PACKAGE 93, OC8STR-Q, PACKAGE 92
(Q,C) |
12.25 |
| OC6STBR7 |
7.5 STRUDDER BRACKET: same as above but
with 7.5 degree angle - as used on PACKAGE 92B or PACKAGE 92D |
13.25 |
|
WEDGE RUDDER ASSEMBLIES |
| OC4WRC |
same as the OC4WR rudder assembly as listed
above but without the mounting bracket. beryllium copper - |
20.95 |
| OC4WRMC |
same as OC4WRM rudder assembly as listed above but
without mounting bracket. beryllium copper
(SEE ILLUSTRATION)
|
24.95 |
|
WEDGE RUDDER BLADES ONLY - extruded
aluminum |
| WRBOL |
LARGE without water pickup hole - 3
3/4"from underside of lower tiller arm to bottom of blade (6 3/8"overall
length)(as used in the (STRUDOFF) offset strudders) |
6.10 |
| WRBOLO |
LARGE with water pickup hole extruded in
the blade - uniquely machined at the top so the water flow is not restricted - 3
3/4"from underside of lower tiller arm to bottom of blade (6 3/8" overall
length)(as used in the strudder M, strudder 750 M, OC8STR-Q, PACKAGE 92, PACKAGE 92B,
PACKAGE 93, OC6WRL (large wedge rudder) or OC6WRL2)(pick up is available machined on the
right or the left, if you have a preference, please let us know) |
6.60 |
| WRBOLX |
Extra long blade with groove for brass
water pick up tube ( brass tube not included) - 4 3/4" from underside of lower tiller
arm to bottom of blade (7 3/8"overall length) |
7.10 |
| WRBOLOX |
x-long rudder blade - 1 1/2" longer
than the WRBOLO with water
pick UP extruded in the back of the blade. Machined pick up available on right or left
side, if you have a preference, please specify - |
7.60 |
|
MISCELLANEOUS |
| OC6PIBR |
STRUDDER RUDDER PIVOT BRACKET -extruded
aluminum - with 2 OC6LTS sleeve bearings
installed as used in strudder M, strudder 750 M, PACKAGE 92 (Q) |
5.95 |
| OC6PIBRD |
STRUDDER RUDDER PIVOT BRACKET - cast
aluminum - with 2 OC6LTS sleeve bearings
installed as used in OC8STR-Q/C strudder packages |
13.25 |
| OC6PIBR2 |
PIVOT BRACKET ONLY - cast aluminum - as
used on the OC6WRL2 - with 2 OC6LTS sleeve
bearings installed |
14.95 |
| OC6WRBR |
WEDGE RUDDER MOUNTING BRACKET - extruded
aluminum - with 2 OC6LTS sleeve bearings installed and four 6-32 t-nuts and bolts- as used
in OC6WRL |
5.95 |
| OCOFFSET |
OFFSET STRUDDER CONVERSIN PACKAGE. Consists
of 2 stainless steel support rods, 1 pivot block with sleeve bearings and 2 10-32 set
screws,l pivot block with 2 10-32 set screws |
12.95 |
| OC6PISH |
RUDDER OR STRUDDER RUDDER PIVOT SHAFT with
E-ring and 2-nylon washers - as used on OC8STR-Q, PACKAGE 93, PACKAGE 92 (Q, B, C, D,),
OC6WRL or OC6WRL2 |
1.35 |
| TA-2 |
TILLER ARMS, fits 3/16" dia.
shaft,molded nylon,wl nut and bolt, (one per package) as used on any of the strudders or
rudders listed above with OC6PISE pivot shaft |
1.15 |
|
PROP BALANCERS |
| OC468PB |
This prop balancer has an extruded aluminum
base and two parallel steel rods for the pro shaft to roll on. It comes complete with a
leveling screw and three prop shaft (1/4", 3/16" & 1/8") which store
within the unit. Instructions are included. |
23.95 |
| OC456PB |
This is the metric version of our handy
prop balancer. It comes with 4mm, 5mm & 6mm prop shafts |
29.95 |
)
) 
